Checking wood moisture

Steve Maxwell gives us the lowdown on effectively drying wood

By Steve Maxwell

wood

No comments

Working with improperly dried wood is like falling into a pit. By the time your plight is obvious, it's too late-assembled parts warp, glue joints crack and a rising sense of panic takes hold. I know because I've felt it. I also know it doesn't have to be this way. Learning about the wily ways of wood can keep you one step ahead of trouble, while letting you enjoy success when using all kinds of inexpensive and interesting lumber that might otherwise cause you grief.

Wood is a moisture sponge-it slowly loses or absorbs moisture from its surroundings. When a piece of wood is in balance with the water in the air around it, the wood is said to have reached equilibrium moisture content (EMC). Whether it's kiln-dried or air-dried, it's all the same. Wood stored in a damp place gets wetter and bigger; low-moisture air makes wood drier and smaller. The trick is ensuring that your wood has a moisture content (and size) in balance with the driest interior environment your completed project is likely to face. Getting to that stage depends on where you start.

Wood is at its wettest as it comes from the sawmill, with a moisture content that can be higher than 30 per cent. If you plan to air-dry your own lumber (which is my preference), you'll need to stack it in a location with at least a little breeze to prevent mould growth and you also need spacers between each layer of wood. A shady outdoor spot is good, and so is an airy shed or hayloft. A garage probably doesn't have enough airflow, and a basement certainly doesn't. This is Phase 1 drying, and it will bring wood moisture content down to about 16 per cent or 12 per cent at the most, depending on the climate in your part of Canada. Just be careful: wood feels ready to use after Phase 1 drying is complete, but it's not nearly dry enough to prevent trouble.

In most regions of the country, wood needs to have a 7 per cent to 9 per cent moisture content to prevent projects from warping and cracking during the driest part of the heating season. Thus, a second drying phase is required, and skipping this step is where most moisture-related trouble starts.

You can store lumber in a barn, unheated garage or shed for a hundred years, and it will never get dry enough for indoor projects. To achieve this low level of moisture, you need a little heat, air and time. How much of these elements depend on the thickness of the wood, how wet it is and the temperature and humidity of your heated, indoor space.

Winter is a great time to dry wood because Canadian homes and heated workshops are ideal Phase 2 drying spaces. And the process doesn't take long if you apply the following three tricks.

Begin by allowing at least a couple of days drying time after each major cutting and planing step. The surfaces of freshly exposed wood need the most drying, and you want this to happen before critical joinery stages. Also, to make the most of this rough-cut drying time, stack project parts with all sides exposed. This could mean standing them up, or stacking them with spacer strips between each layer. To speed Phase 2 drying further, point a household fan at your wood between work sessions. The added air circulation makes wood dry almost twice as quickly.

As you build, don't cut parts down to final size immediately. You want to leave room for wood to do all its misbehaving while it's still larger than needed. Joint, trim and plane each part only after the wood has stabilized. See “Dry for Sure,” at right, if you want more assurance that your wood is actually ready to use.

Learning to dry wood properly isn't the most glamorous workshop skill, but I know for sure that a few moisture-related wood disasters go a long way toward making you an enthusiastic learner.

DRY FOR SURE

A moisture meter isn't absolutely essential for taking the guesswork out of the wood/moisture equation, but it definitely does help. All models work on the same principle. The tool induces a small current through the wood and measures electrical resistance: the lower the resistance, the higher the moisture content. Percentage figures are shown with an analog needle or digital readout. Be sure to measure freshly cut surfaces to get an accurate reading of internal moisture content. As you see how fast wood dries during construction, you'll develop a sense of how long it takes wood to dry to the proper level, and you'll need the meter less and less.


No comments

To leave a comment, please log in

Don't have an user account? Register for free

Poll

How do you heat your home?

Loading ... Loading ...

Recommendations